Easy Quiz 1, Trades & Technology - Automotive

1

Technician A says that if a PCV valve rattles, then it is okay and does not need to be replaced. Technician B says that if a PCV valve does not rattle, it should be replaced. Which technician is correct?

2

Technician A says a Pozidriv screwdriver should be used to remove a clutch head screw. Technician B says a Phillips screwdriver has more grip and less slippage than a Pozidriv screwdriver. Who is correct?

3

Technician A says a bent center link will affect front wheel toe. Technician B says a bent center link willaffect front wheel camber. Who is correct?

4

A 2 foot long spark plug wire is being measured for resistance. The meter reads 38.47 kΩ. Is the wire resistance within specification?

5

Hydroplaning can occur at speeds as low as ________

6

The vision of a company or department describes ________

7

The ignition system is usually split into how many different sections?

8

A bubble balancer performs a(n) [?] balance on a tire and wheel

9

Technician A says that most digital and analog (needle-type) dash gauges use variable resistance sensors. Technician B says that permanent-magnet (PM) generators produce an AC signal and are used for vehicle speed and wheel speed sensors. Who is right?

10

To drive the oil pump and distributor, some overhead cam (OHC) engines use an extra shaft called a(n) _____ shaft that is driven by the crankshaft using an extra sprocket.

11

Technician A says that crossovers are used to block certain frequencies to allow each type of speaker to perform its job better. Technician B says that a high-pass filter is used to block high-frequency sounds being sent to large woofer speakers, and a low-pass filter blocks low-frequency sounds being sent to tweeters. Who is right?

12

A(n) _________________________ is often needed to reach under the molding to release the clip from under the molding lip.

13

In a lock-up torque converter, the ________.

14

Which of the following is not a type of valve used in the valve body?

15

The throttle position sensor used in the throttle body assembly of an electronic throttle control (ETC) system is what type?

16

The dry ERBP of brake fluid ________

17

MAF sensor electrical connectors should be checked for all of these, EXCEPT ________

18

Describe the operation of the accelerator position sensor.

19

Answer the following statements true (T) or false (F)

20

The overrunning clutch accomplishes which of the following?

21

Electromotive force is another term for ________.

22

A "dry park" test to determine the condition of the steering components and joints should be performed with the vehicle _________

23

How many volts does each battery module store in Honda hybrids?

24

What is being checked in this illustration?

25

Briefly describe the three types of circuit defects.

26

Which of these facts is correct about a delta-wound stator?

27

All of the following statements are true EXCEPT:

28

Answer the following statements true (T) or false (F)

29

A painter’s starting transfer efficiency is 46 percent. After training, testing shows that the painter’s transfer efficiency has improved 25 percent. What is the new transfer efficiency level?

30

How many places should the main bearing bore be measured at to check for roundness?

31

Warranties are issued by the vehicle manufacturer for a specified time and mileage.

32

The pinion gear drives the ring gear.

33

While discussing OBD II systems:Technician A says if a misfire condition threatens engine or catalyst damage, the PCM flashes the MIL. Technician B says the PCM illuminates the MIL if a defect causes emission levels to exceed 1.5 times the emission standards for that model year. Who is correct?

34

The TCM compares the desired _______________ pressure with that measured by the _______________ pressure sensor and adjusts the duty cycle of the solenoid accordingly.

35

If greasesweep is used to absorb an oil spill, dispose of it in a regular trash can.

36

The controlling unit for an electronically shifted transmission is the ________

37

Which sensor is also called the ambient air temperature sensor?

38

On many variable displacement engines the cylinder deactivation is done by use of ________

Find your answers, solutions and more...

We made it much easier for you to find exactly what you're looking for on Sciemce. Enjoy our search engine "Clutch."

Save a GPA. Donate your notes with us.

Easy Quiz 1, Trades & Technology - Automotive

Recent Packs