Trades & Technology - Automotive

1

In a circuit with high resistance __________

2

The most important factor upon which customers decide which one to purchase is ________

3

What would normal low and high gauge reading be on a 90° day?

4

An adaptation of the original quality concepts to better fit the needs of business and education is called _______

5

Electronically controlled variable assist power steering systems vary the amount of boost by ________

6

Ring compressors are being discussed. Technician A says that ring compressors are used to remove piston rings on pistons. Technician B says that ring compressors are used when installing a piston into the block. Who is correct?

7

What type of starter motor uses the characteristics of a series motor and a shunt motor?

8

How do hydraulic mounts help prevent noise, vibration, and shock transfer from the differential and suspension to the chassis and vehicle interior?

9

Resistance is defined as the opposition to current flow and is measured in:

10

Using the modified X-method of tire rotation on a front wheel drive vehicle, where should the left front wheel be placed?

11

The clamp opening in a tie rod sleeve must be positioned away from the ______ in the tie rod sleeve.

12

Which of these is most likely to have about 20 kilograms of mass?

13

Clamping diodes ____________

14

The ____ creates the rotating magnetic field of the AC generator.

15

What do you call the service technician's protective head cover?

16

The extra charge a customer may pay for a remanufactured engine until the old engine is returned is called a ____________________.

17

How do you hold the nail tip for application?

18

At higher altitudes, the octane requirement for automobile fuel is ________

19

Technician Asays it is acceptable to rely on visual inspection to determine if a tire is inflated properly. Technician B says that both over-inflation and under-inflation affect brake performance.

20

Some automatically shifted transmissions do not use planetary gear sets. Instead they use ________.

21

Technician A says that exhaust leaks can affect the air-fuel mixture of an engine. Technician B says that exhaust leaks can be dangerous for customers driving their car. Who is correct?

22

The tires on a full-time four-wheel-drive or AWD vehicle should be ________.

23

Induced spark is called ____________________.

24

Technician A says that in an electronic air suspension system if the engine is running, the brake pedal applied, and a door is open, lower vehicle commands are completed immediately. Technician B says that in an electronic air suspension system if the engine is running and a command cannot be completed in 3 minutes, the suspension warning lamp is illuminated. Who is correct?

25

The brake assist system (BAS) is activated ________

26

Which term describes a set of conditions required to allow each monitor to run?

27

Most outboard CV joints are held onto the driveshaft by using a ________ at the end of the shaft.

28

What type of information is commonly included in the owners manual that would be a benefit to the service technician?

29

Two technicians are discussing spark plug gaps. Technician A says that it is critical that spark plug gap be set. Technician B says that a round wire feeler gauge is used to measure gap. Who is correct?

30

What level of tach reference information is required for the PCM to properly control a COP ignition system?

31

During the initial start-up for a rebuilt engine, what rpm should the engine be run at for the first 20 minutes of operation?

32

Which of the following values for IAC count would indicate a vacuum leak on a speed density system?

33

Add 0.102 inch and 0.080 inch. The answer is ________

34

Technician A says that a defective spark plug wire can cause an engine miss. Technician B says that a defective spark plug can cause an engine miss. Which technician is correct?

35

When should the engine oil be replaced?

36

Technician A says that the same recovery unit can be used for R-12 and R-134a. Technician B says that the service hoses from an R -134a recovery unit must have shutoff valves within 18 inches of the end. Who is correct?

37

Explain how the filament type lamp produces light.

38

The goal of job shadowing is to expose the student to the actual "real life" experience of being a professional in the automotive world.

39

Measure the clearance between the tip and body of a rotor type oil pump with a________.

40

All of the following will shut off the high voltage to components and circuits EXCEPT ________.

41

Technician A says that it is a good idea to recommend replacing upper strut bearings when replacing MacPherson struts. Technician B says that all MacPherson struts can be serviced by replacing the cartridge inside the strut assembly. Which technician is correct?

42

Choose the item that describes the best form of advertising

43

Technician A says that RBS type tie rod ends do not require periodic lubrication. Technician B says that the steering gear must be removed to replace outer tie rod ends. Which technician is correct?

44

Shift pressure control solenoids can be used to compensate for ____________ ________ ________.

45

If the vehicle calls for DOT 3 brake fluid then DOT 5 fluid will provide even better performance

46

An organization that sells gas and most likely has a convenience store as part of the operation is known as a(an) ______________ ,

47

Technician A says that heat is measured in degrees. Technician B says that temperature is measured in degrees. Which technician is correct?

48

During a head-on collision with a barrier at 30 miles per hour (mph) or 48 kilometers per hour (km/h), the engine compartment compacts by about 30 to 40 percent of its length.

49

After depleting residual power assist, the brake pedal falls slowly when held down. This indicates a fault with ________

50

Most vehicles have staggered alignment angles to compensate for road crown.

51

A vehicle has a total weight of 3,800 pounds, and 53% of the weight is in the front. Calculate the weight on the rear wheels

52

What component locks the steering wheel in place when the driver removes the key?

53

Technician A says that resistance increases as the diameter of a conductor increases. Technician B says that resistance increases as the temperature of a conductor increases. Which technician is correct?

Find your answers, solutions and more...

We made it much easier for you to find exactly what you're looking for on Sciemce. Enjoy our search engine "Clutch."

Save a GPA. Donate your notes with us.

Trades & Technology - Automotive

Recent Packs