Login
Remember
Register
ScieMce
Find your answers, solutions and more...
We made it much easier for you to find exactly what you're looking for on Sciemce. Enjoy our search engine "Clutch."
Save a GPA. Donate your notes with us.
A manual transaxle jumps out of gear under hard acceleration or deceleration. All of these could be the cause EXCEPT a worn:
asked
Jul 25, 2021
in
Trades & Technology
by
GGLadiesandGents
a. Shift fork
b. Synchronizer sleeve
c. Clutch assembly
d. Transaxle mount
automotive
Please
log in
or
register
to answer this question.
0
Answer
More questions like this
A manual transaxle is suffering from clutch chatter. Technician A says that clutch chatter is caused by glazed clutch facings. Technician B says a worn pressure plate will cause clutch chatter. Who is correct?
asked
Jul 21, 2021
in
Trades & Technology
by
GGLadiesandGents
automotive
The owner of a vehicle equipped with a manual transaxle complained that gear clash was heard whenever shifting. Which is the least likely to be the cause?
asked
Jul 25, 2021
in
Trades & Technology
by
GGLadiesandGents
automotive
A 5-speed manual transaxle has first and second gear, but neutralizes when shifted into third and fourth gear. Fifth gear and reverse are OK. This could be caused by:
asked
Jul 25, 2021
in
Trades & Technology
by
GGLadiesandGents
automotive
A 5-speed manual transmission jumps out of fifth gear while driving. What is the most likely cause?
asked
Jul 25, 2021
in
Trades & Technology
by
GGLadiesandGents
automotive
The shift into reverse in all transaxle slides the reverse idler gear into mesh with a gear on the input shaft and a gear around the 1-2 synchronizer assembly.
asked
Jul 18, 2021
in
Trades & Technology
by
Flambida
automotive
The shift into reverse in all transaxle slides the reverse idler gear into mesh with the gear on input shaft and a gear around the 1-2 synchronizer assembly.
asked
Jul 18, 2021
in
Trades & Technology
by
PowerG
automotive
A five-speed manual transaxle is noisy in all gears. Which is the least likely cause?
asked
Jul 25, 2021
in
Trades & Technology
by
GGLadiesandGents
automotive
A front-wheel drive vehicle with a 5-speed manual transaxle will not shift into REVERSE. All forward gears work normally. The most likely cause is:
asked
Jul 25, 2021
in
Trades & Technology
by
GGLadiesandGents
automotive
A customer complained of hard shifting, particularly into first gear and reverse. Technician A says that the blocking ring may be worn. Technician B says that the clutch may be defective or out of adjustment. Which technician is correct?
asked
Jul 25, 2021
in
Trades & Technology
by
GGLadiesandGents
automotive
Technician A says that excessive radial play of the axle at the outer end can be caused by a worn or bent axle. Technician B says that a gear oil leak onto the brakes can be caused by a bad seal or gear oil level that is too high. Which technician is correct?
asked
May 7, 2022
in
Trades & Technology
by
Ecollett7399
automotive
An automatic transaxle slips only while turning corners. Which of the following has caused this condition?
asked
Dec 5, 2021
in
Trades & Technology
by
GGLadiesandGents
automotive
A growling sound is heard with the engine running and the transaxle is in neutral with the clutch engaged (foot off of the clutch pedal). What is the most likely cause?
asked
Jul 25, 2021
in
Trades & Technology
by
GGLadiesandGents
automotive
A growling sound is heard when the engine is running and the transmission/transaxle is in neutral with the clutch engaged (foot off of the clutch pedal). The noise stops when the clutch pedal is depressed. What is the most likely cause?
asked
Jul 25, 2021
in
Trades & Technology
by
GGLadiesandGents
automotive
A transfer case used with a transaxle is called a coupler device.
asked
Jul 18, 2021
in
Trades & Technology
by
kmyrs97
automotive
On a transaxle, all of the speed gears are attached to the input shaft with lock rings.
asked
Jul 18, 2021
in
Trades & Technology
by
ShearElegance
automotive
A typical transaxle repair kit only consists of snap rings and gasket.
asked
Jul 18, 2021
in
Trades & Technology
by
kcmorrison13
automotive
All the gears of a transaxle are helical cut.
asked
Jul 18, 2021
in
Trades & Technology
by
Djurdjic
automotive
Operations of the synchronizers in a transaxle are the same as those in a transmission.
asked
Jul 18, 2021
in
Trades & Technology
by
Kindred
automotive
The final drive ring and pinion gears in a typical transaxle are spiral bevel gears type.
asked
Jul 18, 2021
in
Trades & Technology
by
htmatrix
automotive
All the gears in the transaxle are in constant mesh.
asked
Jul 18, 2021
in
Trades & Technology
by
Maggie
automotive
Welcome to Sciemce, where you can ask questions and receive answers from other members of the community.
Recent Packs
ch 10
25
items
by
Kingrick09
automotive
#8
74
items
by
kooch54071
introduction-to-business
automotives
21
items
by
Kingrick09
automotive
Multicultural Issues in LE
20
items
by
thanasis458
electives-upper-level
2
51
items
by
dagogonz
business-law
kdfne4
19
items
by
dagogonz
business-law
quiz 15
10
items
by
scrumpadoo
american-government-and-politics
mis
76
items
by
alerods22
management-information-systems
Final
31
items
by
j.lopezrojas1
management-information-systems
mis
82
items
by
lara gggggg
management-information-systems
help 2
11
items
by
BillyLuu
social-and-applied-psychology
new
20
items
by
marcustbg
introductory-astronomy
1
6
items
by
nwdr
management
Final Exam
48
items
by
MM1122
automotive
final exam
50
items
by
ehbdehbiefbef
automotive
chapter 10
14
items
by
MM1122
automotive
Research Final
47
items
by
griffs110
correctional
pm
48
items
by
yuny
decision-science
Bossbot
17
items
by
Champ
developmental-psychology
3
18
items
by
isabellaw123
marketing
...