In controlling motor operations, what are the two general schemes used to deliver the DC to the motor?
What will be an ideal response?
One block provides DC to the field, and one block supplies controlled DC to the armature.
You might also like to view...
Nonconductive grommets or plastic bushings should be used to prevent a destructive galvanic reaction between steel framing members and _____.
a. copper piping b. aluminum siding c. nonmetallic sheathed cable d. PVC piping
Two different scales are used in measuring temperatures. These scales are called Fahrenheit (F) and ____________________ (C).
Fill in the blank(s) with the appropriate word(s).
List the materials commonly used to construct duct systems
What will be an ideal response?
Error correction using three FDMA orthogonal signals. The following worksheet specifies three 10- sample FDMA orthogonal data signals: sA1 in B5:B14, sB1 in C5:C14 and sC1 in D5:D14. Random transmitted bit Dt is computed in C1. The transmitted signal sATi (in E5:E14) = sAi if Dt=1 and =-sAi if Dt=0. The transmitted signal sBTi (in F5:F14) = sBi if Dt=1 and =-sBi if Dt=0. The transmitted signal sCTi (in G5:G14) = sCi if Dt=1 and =-sBi if Dt=0. The Gaussian noise sequence Ni SD ?N is specified in I1. The detected signal Xi is computed as the sum of the three signals and noise in I5:I14. The matched processor component sAiXi is computed in J5:J14 and VA is computed in J16. The matched processor component sBiXi is computed in K5:K14 and VB is computed in K16. The matched processor
component sCiXi is computed in L5:L14 and VC is computed in L16. The detected bit DAr is computed in B2 from VA, DBr is computed in D2 from VB, and DCr is computed in F2 from VC. The received data bit Dr in E2 is computed using error correction applied to DAr , DBr and DCr
The probability of error is estimated by computing the ratio of errors to transmitted data in O5 as the noise ?N varies from 0 in steps of ?? = (Es/2)1/2 using Es computed in I2. The total number of data bits to be transmitted nT is specified in O2. The number of transmissions accomplished in shown in O3 – with 1 bit per three-signal transmission - and the number of errors in O4. Three VBA Macros are present:
The probability of error is estimated by computing the ratio of errors to transmitted data in O5
as the noise ?N varies from 0 in steps of ?? = (Es/2)1/2 using Es computed in I2. The total number
of data bits to be transmitted nT is specified in O2. The number of transmissions accomplished in
shown in O3 – with 1 bit per three-signal transmission - and the number of errors in O4. Three
VBA Macros are present:
? ResetEC resets the counts in O3 and O4.
? XmitEC increments the number of transmissions by one for each signal transmission
and, if an error occurs (Dr ? Dt) increments the error count.
? AutoEC computes the P[error] for nT transmissions as ?N varies and displays the results
in N8:O16.
a. What is the formula in C1?
b. What is the formula in E10?
c. What is the formula in F10?
d. What is the formula in G10?
e. What is the formula in H10?
f. What is the formula in I10?
g. What is the formula in K10?
h. What is the formula in K16?
i. What is the formula in B2?
j. What is the formula in D2?
k. What is the formula in F2?
l. What is the formula in E1?
m. What is the formula in 01?
n. What is the formula in O5?
o. Compose ResetEC.
p. Compose XmitEC.
q. Compose AutoEC.
