Let Quiz 4,Trades & Technology - Automotive

Design requirements for vehicle brakes include ________

Technician A says electronically controlled systems may use sensor inputs to control the center differential for front-rear torque bias. Technician B says the Porsche PTM system uses an electronically controlled motor in the transfer case. Who is correct?

3

What is the maximum amount of warpage allowed on an aluminum head before it must be resurfaced?

4

A typical radar cruise control system uses ________

5

The composite vehicle is running poorly. The technician has recorded the following data: Engine Idle Speed700 RPMMass Air Flow sensor0.7 voltsMAP sensor2.1 volts Technician A says a faulty MAP sensor is the cause. Technician B says the Mass Air Flow sensor is defective. Who is right?

6

An engine knock may occur due to:

7

Recirculating steel balls are used in most conventional steering gears because they ________

8

With how much interference is a cylinder sleeve installed?

9

The throttle body may need cleaning if which of the following occurs?

10

A(n) ____ requires the ignition switch to be off for a period of time.

11

What are the steps involved in the use of a ridge remover tool?

12

Which type of hybrid electric vehicle has idle stop operation?

13

Which type system uses a one speed transfer case and a center differential with a viscous coupling?

14

The Chevrolet Volt uses input from the ____ to identify the severity of a collision and from what direction a collision has occurred.

15

An EGR valve that is partially stuck open would most likely cause what condition?

16

The driven gear has 85 teeth. The driver gear has 15 teeth. Find the ratio of the teeth on the driven gear to the driver gear.

17

During the SWOT analysis, the question that many employees have the hardest time addressing is identifying their _________

18

This would NOT be one method/tool of finding a refrigerant leak in the system:

19

What changes mechanical energy to electrical energy?

20

What helps prevent water pump cavitation?

21

When does the PCM perform a self test of the ETC system?

22

The most popular universal joint design is called a ____.

23

While discussing the numbering of HO2S sensors, Technician A says they are identified by their position in relation to the number 1 cylinder and their location relative to the converters. Technician B says HO2S sensors on the same side of the vehicle as the number 1 cylinder have a 1 prefix, and sensors mounted downstream from the converter have a 1 suffix. Who is correct?

24

What is true of ULEV II vehicles?

25

The chemical energy in fuel is converted to heat by the burning of the fuel at a controlled rate. This process is called ________

26

A vehicle vibrates at highway speed. Technician A says that water in the tire(s) could be the cause. Technician B says that an out-of-round tire could be the cause. Which technician is correct?

27

When charging a lead-acid (flooded-type) battery, ________

28

The caliper dust boot may need to be pried out with a(n) ________

29

ASE-Style Multiple Choice ____ are items such as the keyboard or bar code reader that allow you to put information into the computer.

30

All of these are correct EXCEPT ________

31

The electric AIR pump is energized ________

32

Type "B" misfire codes are set if the misfire exceeds ________ to ________, depending on the engine, make, model, and year

33

Which electronic component inside the ignition module opens and closes (switches) the primary ignition circuit?

34

An electrical circuit using 12 volts and having 10 ohms of resistance would have a current of:

35

Technician A says grounding out a plug wire to a cylinder with a cracked piston will can increase the noise. Technician B says a rod knock will become quieter as its cylinder is grounded. Who is correct?

36

Some systems also have a ________ sensor between the throttle body and the air cleaner

37

What are the six clutch components that should be inspected and measured?

38

ASE-Style Multiple Choice A ____ picks up bits of filler dust that normal cleaning leaves behind.

39

How can you reduce an engine's power output?

40

A P0117 DTC is being discussed. Technician A says that the ECT sensor could be internally shorted to ground. Technician B says that the signal wire could be open. Which technician is correct?

41

A large amount of oxygen in the exhaust system causes the O2S to produce which of these?

42

Two technicians are discussing why the brake lines are coiled near the master cylinder on many vehicles. Technician A says that these coils help prevent moisture from flowing from the master cylinder to the calipers. Technician B says that they help prevent cracks that could be caused by vibrations. Which technician is correct?