Let Quiz 3/Trades & Technology - Automotive

A TSI test is automatically aborted after 10 sec-onds in the high-speed mode. Refer to the test results to determine the validity of the technicians' statements

11

Technician A says that automatic adjusters adjust the lining-to-drum clearance when the brakes are applied. Technician B says that they adjust the clearance when the brakes release. Which technician is correct?

12

Under the leadership of Richard Allen, black delegates from Pennsylvania, New York, Delaware, Maryland, and Virginia endorsed immigration of free black Americans to __________

13

Two technicians are discussing which lubricants are used in a limited-slip differential. Technician A says to use SAE 80W-140. Technician B says that most vehicle manufacturers usually specify SAE 80W-90 be used with or without special limited-slip additives. Which technician is correct?

14

Which of the following clutches serves to reduce friction, limits the production of heat, improves overall performance, increases the life of the clutch assembly, and is capable of handling large amounts of torque?

15

A hydraulic press is being used to separate a bearing from a shaft. What should be used to cover the bearing during the pressing operation?

16

In modern GM engines, what type of sensor is the throttle position sensor (TPS)?

17

Backlash is the amount of movement between the tooth contact of two gears in mesh.

18

While discussing transmission adaptive learning: Technician A says this learning process allows the TCM to make adjustments to its program so that quality shifting always occurs. Technician B says the TCM learns to respond to the driver's driving habits. Who is correct?

19

A leaking axle seal may cause the drum brakes to make a grinding noise.

20

Which of the following is true regarding the cabin air filter?

21

Technician A says the outer ring of the vibration damper can slip out of position. Technician B says the most vibration occurs at the rear of the crankshaft. Who is right?

22

Inputs in the electronic variable orifice (EVO) steering system include the:

23

What type of balance is checked with the tire stationary?

24

The minimum cut when machining a drum or rotor should be ________

25

What are the possible causes of a rapidly clicking solenoid?

26

The torque specification for a valve cover gasket is 5 foot-pounds. Which of the following is the best procedure?

27

For proper tracking what must be positioned over the centerlines of the front and rear axles?

28

Focus groups of individuals from the community are often convened to conduct a ________

29

All of the following statements are true EXCEPT:

30

Technician A says an antilock system that operates on the select-low principle will control each rear wheel individually. Technician B says systems using the select-low principle regulates rear wheel brake pressure to both rear wheel simultaneously. Which technician is correct?

31

What happens when fuel lines get too hot and only fuel vapors go through the fuel injectors?

32

Which is NOT a commonly used type of fuel pump design?

33

Technician A says that it is recommended that the vehicle be driven less than 50 mph for the first 50 miles to allow the tire to adhere to the wheel. Technician B says that sudden hard acceleration with newly mounted tires can cause the tire to change position on the wheel. Which technician is correct?

34

Of the alternative fuels listed in the text, which has the highest octane?

35

36

In automotive wiring systems, a terminal is made of ________

37

Technician a says that a scan tool may be required to retrieve data and diagnostic trouble codes from some antilock braking systems. Technician B says that a jumper wire can be used to retrieve diagnostic trouble codes on some antilock braking systems. Which technician is correct?

38

796 + 218 =

39

Which statement is true concerning a breakout box?

40

Speaker polarity can be tested using a small battery

41

ASE-Style Multiple Choice ____ are used for fast removal of material.

42

The proper height for lifting should place the work area ________

43

The Honda Insight was designed to have a driving range of 1,000 miles.

44

The ICE will start on most hybrid electric vehicles when the sate-of-charge of the HV battery drops to

45

A General Motors Passkey III system has the transponder located in the ________

46

Technician A says that the location of the catalytic converter is not important. Technician B says that the catalytic converter should be positioned as far from the engine as possible. Which technician is correct?

47

How much voltage is generally available to fuel injectors (most vehicles)?

48

Two technicians are discussing differentials. Technician A says that all differentials are vented. Technician B says that a clogged vent can cause the rear axle seal to leak. Which technician is correct?

49

Describe the noise caused by an excessively worn crankshaft main bearing.

Find your answers, solutions and more...

We made it much easier for you to find exactly what you're looking for on Sciemce. Enjoy our search engine "Clutch."

Save a GPA. Donate your notes with us.

Let Quiz 3/Trades & Technology - Automotive

Recent Packs