Quiz Fall 8-Trades & Technology - Industrial And Skilled Trade

1

The four types of soft foot that may exist are parallel soft foot, angular soft foot, ____ soft foot, and induced soft foot.

2

The ____ joint is made when one piece of metal is laid over the edge of another.

3

A medication preparation area in a nursing home may have alternate power connected via a delayed automatic transfer device during a power failure in a _____.

4

If the G-code is G20 G91 F6 G01 Z1.00:

5

With ____________________ testing all welds can be tested and the part can be used for its intended purpose.

6

The heat content of one gallon of No. 2 fuel oil is about ____________________ Btu.

7

All of the following are factors in a tractor-trailer's ability to stop EXCEPT:

8

In refrigeration and air conditioning, safety controls are wired:

9

When a cranking circuit is energized, a series of rapid clicks is heard with a no-crank condition. Technician A says that this could be caused by discharged batteries. Technician B says this could be caused by corrosion on the starter insulated terminal. Who is correct?

10

Three phase motors have ____.

11

Actual measurements for construction are taken from the _____

12

Which of the following is a true statement regarding the personnel roles in a crane lift?

13

Why is it important to document inspection results and materials used during each step of the PM activity and not waiting until the end of the day?

14

NFPA 70E® provides practical guidance in _____.

15

A trainee must demonstrate knowledge of the hands-on tasks learned in each module. This is referred to as _____.

16

Problems in the refrigerant portion of a system are caused by ____.

17

In the alphabet of lines, an area not included in the cutting line view is shown with _____

18

What is the best way to tell if a disposable refrigerant cylinder is equipped with a dip tube

19

In a(n) ____________________ fuel oil supply system, one pipe is the supply and the other acts as the return.

20

¿Qué indica una quemadura grande en el clavo?

21

The US DOL has made it easier for high school students to prepare for a career as a craft professional through _____.

22

It is important to the HVACR technician to understand the changes of state of matter because:

23

You are standing with your back to the hinge side of the door jamb. The door swings to your left, so you know

24

Which type of fit-up tool is often used to fit flanges and where heavy-duty reforming of the pipe is required?

25

A stress riser is a point of stress concentration usually caused by an abrupt change in the thickness or _____ of a material or the presence of a sharp groove or crack on the material's surface.

26

____________________ materials have no orderly arrangement of their atoms into crystals.

27

Referring to the following figure, the A/C compressor would not be energized with the Mode Switch in the A/C position and the blower switch in the OFF position.<img width="546" height="782" align="bottom" src="https://sciemce.com/files/3/ppg__examview__bell_mdtee2e_tb_images__Chapter_10_tf010-1.jpg" border="0">

28

________ must be set at appropriate locations for the concrete to be efficiently placed and leveled

29

The Robot Institute of America states that a(n) ____________________ robot is a "reprogrammable, multifunctional manipulator designed to move material, parts, tools, or specialized devices through variable programmed motions for the performance of a variety of tasks."

30

If pipes of greatly different lengths must be lifted, _____.

31

Technician A says that Hall-effect throttle position sensors (TPS) are configurable to either digital or analog input circuits as required by the application. Technician B says that a disadvantage of Hall-effect TPS is that the contact wiper wears at an accelerated rate. Who is correct?

32

238.237 - 190.30 x 0.372 + 32.9303 x 2 = ____. Round to two decimal places.

33

Heating cable for snow-melting is typically installed in a serpentine pattern with loops spaced at _____.

34

A hot water heating system is installed in a house. The system needs 140 feet of 3/4-inch copper tubing. The tubing lists for $1.70 per foot. A 10% discount is given. How much does the tubing cost? Round the answer to the nearer whole cent.

35

Which of the following is not what one of the SWOT initials stands for?

36

What causes coolant that was expelled from the system to the expansion tank to be return to the cooling system as the engine cools?

37

La Figura 1 indica que la información sobre el panel A se encontrará en:

38

The travel of a piping offset that has a run of 15 inches and an angle of 45 degrees is _____ inches. (Refer to the figure above.)

39

To weld stainless steels, the arc should be as long as possible.

40

Una sierra circular portátil tiene _____.

41

For each 12,000 Btu/h capacity, a wastewater-cooled condensing unit uses approximately ____________________ GPM.

42

What use is THHN wire suitable for?

43

The feed on a lathe is set for 1/128 inch. How many revolutions does the work make when the tool advances 5 1/4 inches?

44

What benefit is there to the student in taking the ICE exam?

45

The main cause of high condensing temperature and pressure in air-cooled condensers is:

46

Simplify the expression: 36 - (M3 + M) + (M3- 12).

47

Refer to the figure. Assume 1" copper. Find e-e of L if J=12"<img width="375" height="241" align="bottom" src="https://sciemce.com/files/4/ppg__examview__i24__00001_res__nr004-1.jpg" border="0">

48

Technician A says that a cathode has an excess of electrons. Technician B says when a cathode is connected to an anode by a conductor, electrons will flow from the cathode to the anode. Who is correct?

49

Define parallel alignment.

50

As an apprentice, if you find a discrepancy between the plan drawings and specifications for a job, you

51

Convert -100° Celsius to Kelvin

52

What are the three basic types of armature windings?

53

What is another way of saying smart switch?

54

The number of basic grades in which Plyform sheets for form building are available is _____.

55

One advantage of part winding starters is that they provide ____________________ starting because the motor is never disconnected from the power line during the starting time.

Find your answers, solutions and more...

We made it much easier for you to find exactly what you're looking for on Sciemce. Enjoy our search engine "Clutch."

Save a GPA. Donate your notes with us.

Quiz Fall 8-Trades & Technology - Industrial And Skilled Trade

Recent Packs