Quiz a lot 8. Trades & Technology - Industrial And Skilled Trade

1

If there was a complete electrical failure in an electronically-managed Bosch PE 8500 fuel pump, which of the following would result?

2

Expansionary monetary policy actions

3

Although connecting components to a terminal strip generally involves using a greater amount of wire, it can be the less expensive method when it is necessary to ____________________ the circuit.

4

Which of the following is true with regard to TTC zones?

5

What is the difference between primary air and secondary air?

6

Las tuberías de gas caliente se aislan cuando se ubican _____.

7

A building frame is usually considered to be rigid in only _____.

8

Beside maintaining pressure on the contacts for current carrying capacity, the pressure springs have a second important function. This is to ____.

9

According to the text, the minimum distance stakes and batters boards are set back from the building corners is ________ feet

10

When one side of the secondary winding of a control transformer is grounded, the control system is referred to as a(n) ____________________ system.

11

Express 19.225 as a percent.

12

A new city hall is built with a circular floor. The floor is 80 feet 6 inches in diameter. It is two stories high. Each story is 12 feet high. What is the volume of the building?

13

Most welding hoses used today are molded together as one piece and are referred to as ____________________ hose.

14

A normal calibration involves setting the zero and _____

15

When laying out a stringer using a framing square, the blade of the framing square represents the _____

16

To better spread the load supported by a caisson, the bottom of the caisson hole may be widened by a process called _____.

17

El cable de fibra óptica vertical se debe ajustar cada:

18

A modern hydronic heating system typically:

19

What is the difference between the recovery time objective and the recovery point objective?

20

A flange that is double-welded to the pipe is known as a _____ flange.

21

A test taken in the ____ position would usually allow the welder to work in the flat, horizontal, and vertical positions, depending on the code requirements.

22

The specification for the size of ____ is given as the outside diameter.

23

Solve the following system of equations by graphing:5x + y = -32x- 3y = -8

24

Answer the following statement(s) true (T) or false (F)

25

If a varnish-like substance has formed on an oil burner nozzle, it indicates that the _____.

26

Los cabezales de pilote se usan para _____.

27

The bearing failure that is evidenced by a rolling element track in the raceway is _____

28

What is used to seal fuel in the plunger/pump chamber from the cambox in a typical port-helix metering pump?

29

¿Qué debe usarse para asegurarse de hacer cortes derechos en las planchas de fibra de vidrio?

30

With the aid of Appendix B and Appendix E, make a sketch similar to those in Fig. 17.13 for the case of (1012) twinning in cadmium.

31

The state of matter depends upon:

32

Tiene que haber un pulsador manual dentro de los _____ de recorrido horizontal en el mismo piso desde cualquier parte del edificio.

33

Refer to the figure. Determine the diagonal<img width="428" height="279" align="bottom" src="https://sciemce.com/files/4/ppg__examview__ch38__00001_res__nr002-1.jpg" border="0">

34

Conflict resolution is considered to be a(n) _____

35

Which government agency is involved in setting gas-fired equipment standards?

36

The condenser is designed to:

37

Belt tension will not have any affect on the wear of the bearings.

38

La ubicación de la cama de cada paciente debe contar con el suministro eléctrico de _____ circuito(s) derivado(s).

39

The thermostat for room units is usually mounted with the control knob in the control center and the remote bulb in the vicinity of the return air.

40

Which of the following statements about the use of turnbuckles is correct?

41

After installation, butt joints of sheet insulation sections on duct and equipment should be ______.

42

What type of VG turbochargers are used by most current diesel engine OEMs?

43

Which torch type would be the best choice for a brazing project?

44

In order to thread steel pipe, ____________________ is applied so friction and heat do not damage the pipe and/or cutting dies.

45

Which of the following is not recommended when cutting pressure-treated lumber?

46

The frequency of motor lubrication depends on the type of bearing, motor application, and _____.

47

When setting up the welding equipment for GMAW on aluminum pipe, the proper shielding gas to use is

48

Which of the following condensers is the most efficient?

49

What should you do before lifting or lowering the hood on a conventional truck?

50

On a winder stairway, the winder tread width at a point 12ʺ from the narrower end of the winders must be

51

If a tractorʹs hitch is to be used for towing a PTO-driven attachment, the ideal vertical distance between the

52

What tests can a technician perform on an oil furnace that will check the combustion efficiency?

Find your answers, solutions and more...

We made it much easier for you to find exactly what you're looking for on Sciemce. Enjoy our search engine "Clutch."

Save a GPA. Donate your notes with us.

Quiz a lot 8. Trades & Technology - Industrial And Skilled Trade

Recent Packs